Repack Wheel Bearings
#1
Thread Starter
Join Date: Feb 2004
Location: Redmond, Oregon, USA
Posts: 2
Likes: 0
Received 0 Likes
on
0 Posts
Repack Wheel Bearings
I have read a lot of people replacing there wheel bearings, and I am replacing the rotors on my 94 lx and had to remove the bearing so I figure I might as well clean the bearing out and regrease them. I have no reason to believe that they are bad. Does anyone see a problem with this?
#2
We sell parts.
Join Date: Mar 2002
Location: Lexington, KY
Posts: 2,063
Likes: 0
Received 0 Likes
on
0 Posts
Re: Repack Wheel Bearings (Nhilcrest)
Well if they have never been replaced, i would replace them. No sense in doing a job 2x. If they have been replaced in the car's life i would not change them.
#5
Honda-Tech Member
Join Date: Oct 2003
Location: Nashville, Tn, USA
Posts: 1,038
Likes: 0
Received 0 Likes
on
0 Posts
Re: Repack Wheel Bearings (BVH)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by BVH »</TD></TR><TR><TD CLASS="quote">They are sealed bearings you can't re-pack them.</TD></TR></TABLE>
Took the words right out of my mouth.
Took the words right out of my mouth.
#6
Re: Repack Wheel Bearings (BVH)
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by BVH »</TD></TR><TR><TD CLASS="quote">They are sealed bearings you can't re-pack them.</TD></TR></TABLE>
This is absolutely true. You can NOT repack them.
This is absolutely true. You can NOT repack them.
Trending Topics
#11
Re: Repack Wheel Bearings
I'm sorry but you guys are incorrect. You can pop the inner races out of a sealed bearing, clean and regrease the bearings and pop the inner races back in. The cage inside the bearing is plastic and can flex. This allows the races to be popped out without damaging anything. It's tricky, and you CAN damage the bearing assembly when doing this.
Though, there is no reason to do this. Since it's a sealed bearing, if the bearing is good, so is the grease. The only time this would be considered practical is if you are separating the hub for some reason and the inner race comes out with the hub. You can put the bearing back together without a problem assuming the bearing cage is still plyable. Other than that, I'd just leave the bearing alone.
Though, there is no reason to do this. Since it's a sealed bearing, if the bearing is good, so is the grease. The only time this would be considered practical is if you are separating the hub for some reason and the inner race comes out with the hub. You can put the bearing back together without a problem assuming the bearing cage is still plyable. Other than that, I'd just leave the bearing alone.
#12
Honda-Tech Member
Re: Repack Wheel Bearings
I'm sorry but you guys are incorrect. You can pop the inner races out of a sealed bearing, clean and regrease the bearings and pop the inner races back in. The cage inside the bearing is plastic and can flex. This allows the races to be popped out without damaging anything. It's tricky, and you CAN damage the bearing assembly when doing this.
Though, there is no reason to do this. Since it's a sealed bearing, if the bearing is good, so is the grease. The only time this would be considered practical is if you are separating the hub for some reason and the inner race comes out with the hub. You can put the bearing back together without a problem assuming the bearing cage is still plyable. Other than that, I'd just leave the bearing alone.
Though, there is no reason to do this. Since it's a sealed bearing, if the bearing is good, so is the grease. The only time this would be considered practical is if you are separating the hub for some reason and the inner race comes out with the hub. You can put the bearing back together without a problem assuming the bearing cage is still plyable. Other than that, I'd just leave the bearing alone.
Thread
Thread Starter
Forum
Replies
Last Post
immalooser
Honda Accord (1990 - 2002)
5
02-28-2006 12:44 AM